Personal Protective Equipment For Electrical Hazards

47 Slides4.63 MB

Personal Protective Equipment For Electrical Hazards

Introduction This material was produced under grant number SH-16615-07-60-F-12 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily reflect the views or policies of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. Government. This material was produced by the Workplace Safety Awareness Council, a 501(c)(3) not-for-profit organization dedicated to safety in the workplace. For further information about the council or upcoming safety related training, please visit our website at www.wpsac.org or call us at (863) 537-4053.

Hierarchy of Control 1910 Subpart I Appendix B Engineering Solutions: Guards Barriers Design Features Administrative Solutions: Employee Training Standard Operating Procedures Hot Work Permit Personal Protective Equipment: FR Clothing Hard Hat Safety Glasses Remember – PPE is a last line of defense!

Alerting Techniques 1910.335(b)(1)-(3) Other examples to protect employees from electrical hazards: Safety signs and tags Barricades Attendants

PPE Requirements 1910.335(a)(1)(i) Employers Must determine what is needed (JHA) Must train employees on proper use Must enforce use of PPE May be required to pay for the PPE Employees must use the PPE!

Why is FR Needed? Most severe burn energies and fatalities are caused by non-flame resistant clothing igniting and continuing to burn Flame resistant clothing will self-extinguish, thus limiting the injury Body area under non-FR clothing is often burned more severely than exposed skin

Arc Energy vs Distance Energy goes up dramatically as distance from arc drops: EXAMPLE: 22,000A, 480V, 6 cycles: 24” 18” 15” 12” 2.7 cal. 3.2 cal. 7.5 cal. 12.2 cal. 10” 18 cal. How close are you to the arc?

What PPE Do I Have to Wear NFPA uses a three-step process: Step 1: Determine the Hazard / Risk Category Classification based on NFPA 70E Table 130.7(C)(9)(a) Task Hazard / Risk V-Rated Category Gloves Panelboards & Switchboards 240V and up to 600V 0 No CB or Fuse Switch Operation With covers ON CB or Fuse Switch Operation With covers OFF Work on energized parts, including voltage testing V-Rated Tools No 1 No No 2* Yes Yes These tables are used for demonstration purposes only. Always refer to NFPA 70E for actual requirements

NFPA Hazard Risk Categories Step 2: Select Protective Clothing and PPE based on NFPA 70E Table 130.7(C)(10). Personal Protective Clothing FR Clothing: Hazard / Risk Category Number -1 1 2 3 4 Long-sleeved Shirt X X X X Pants X X X X Coverall 0 (Note 5) (Note 7) Jacket, Parka, Rainwear AN AN X (Note 5) (Note 9) AN These tables are used for demonstration purposes only. Always refer to NFPA 70E for actual requirements AN

NFPA Hazard Risk Categories NFPA 70E Table 130.7(C)(10) – Continued. . . Personal Protective Equipment FR Protective Equipment: Hazard / Risk Category Number -1 0 Hard Hat Safety Glasses X X 1 2 3 4 X X X X X X X X X Flash Suit Hood Hearing Protection X (note 8) These tables are used for demonstration purposes only. Always refer to NFPA 70E for actual requirements

NFPA Hazard Risk Categories Step 3: Identify Minimum ATPV and System based on HRC From Table 130.7(C)(11) Hazard Risk Category 0 1 2 3 4 Typical Protective Clothing Systems Clothing Description (number of layers in parenthesis) Non Melting Flammable Materials (1) FR Shirt and FR Pant or FR Coverall (1) Cotton Underwear PLUS FR Shirt and FR Pant or FR Coverall (1-2) Cotton Underwear PLUS FR Shirt and FR Pant or FR Coverall (2-3) Cotton Underwear PLUS FR Shirt and FR Pant PLUS Double Layer Switching Coat and Pants (3 or more) Minimum ATPV N/A 4 8 25 40 These tables are used for demonstration purposes only. Always refer to NFPA 70E for actual requirements

Arc Thermal Protection Value Arc Thermal Protection Value (ATPV) is defined by ASTM F 1959-00 as: “the incident energy on a fabric or material that results in sufficient heat transfer through the fabric or material to cause the onset of a second degree burn based on the Stoll Curve”

The 70E Solution Confused by the selection process? National trend is single layer HRC 2 daily wear and HRC 4 flash gear Don’t let confusion delay your PPE selection!

What is Flame Resistant Clothing? Clothing made from fabrics that selfextinguish Fabrics may be natural or synthetic Designed to limit (not eliminate) burn injury Survival, extent of injury, recovery time and quality of life are all dependent on FRC performance

Engineered Flame Resistant Fabrics Natural fibers Synthetic fibers Natural / synthetic blends NOTE: Flame resistance must be durable to launderings, wear, the environment, etc. for the service life of the garment Look for proven products!

New World of FRC FRC used to be perceived as ugly, uncomfortable, expensive, scratchy, hot and not breathable Major shift last 3-5 years to lighter, softer more breathable fabrics and to styles virtually identical to “street clothing” Examples include Nomex/Rayon blends, Indura UltraSoft , knits, fleeces, denims.

Proper Use FRC should be appropriate to hazard Always the outermost layer Worn correctly; zipped, buttoned, etc All natural, non-melting undergarments Clean, no flammable contaminants Repaired correctly and removed from service when needed

Insulating Gloves: Types Insulating gloves come in two “type’s”: Type I Pro: Greater flexibility and “feel” Con: Not ozone-resistant, will crack if exposed to ozone or UV over time. Type II Pro: Ozone-resistant. Con: Not as comfortable to wear (less flexible)

Insulating Gloves: Class FAST FACT: Remember, it’s not the color of the glove that’s important – it’s the color of the tag!

Glove Markings 1910.137(a)(1)(iv) Class & Type designations are found on the cuff portion of the glove.

Protector Gloves 1910.137(b)(2)(vii)(A) Protector gloves must be worn over insulating gloves, except for Class 0 gloves, under limited-use conditions, where small equipment and parts manipulation necessitate unusually high finger dexterity. FAST FACT: Do not use leather protectors alone for protection against electric shock. Serious injury or death could result. Always use proper rubber insulating gloves.

Glove 1910.335(a)(1)(ii) 1910.335(a)(1)(ii) Protective equipment shall be maintained in a safe, reliable condition and shall be periodically inspected or tested, as required by 1910.137. 1910.335(a)(1)(iii) If the insulating capability of protective equipment may be subject to damage during use, the insulating material shall be protected. (For example, an outer covering of leather is sometimes used for the protection of rubber insulating material.)

Glove Testing 1910.335(a)(1)(ii) Protective Equipment Testing Schedule Equipment When to Test Gloves Before first issue and every six months after that.* Blankets / Sleeves Before first issue and every 12 months after that. Line Hose / Covers equipment Upon indication * If the protective has been that electrically insulating value is tested, but not issued for use it devalued. may not be placed in service unless it has been electrically tested within the previous 12 months.

Eye Protection 1910.335(a)(1)(v) Eye protection is required whenever there is danger of injury to the eyes or face from electric arcs or flashes or from flying objects resulting from electrical explosion. Remember: If using face shield for arc flash protection be sure to check the Minimum ATPV rating (in cal/cm²)

Eye Protection Markings 1910.133(a)(4) & (b)(1) - (2) PPE for eye and face protection purchased after July 5, 1994 shall comply with ANSI Z87.1-1989 or shall be demonstrated by the employer to be equally effective. PPE for eye and face purchased before July 5, 1994 shall comply with the ANSI "USA standard for Occupational and Educational Eye and Face Protection," Z87.1-1968 or shall be demonstrated by the employer to be equally effective. Eye and face PPE shall be distinctly marked to identify the manufacturer.

Head Protection 1910.335(a)(1)(iv) & 1910.135(b)(1) Protective helmets purchased after July 5, 1994 shall comply with ANSI Z89.1-1986 FAST FACT: ANSI has revised its Z89.1 standard a few times since 1986 and its most current standard is ANSI Z89.1-2003. OSHA however, still references the 1986 standard. As a practical matter if you comply with any of the ANSI Z89.1 standards from 1986 onward, you are compliant with OSHA.

Helmet Type (Pre-1987) ANSI Z89.1-1986 separates protective helmets into two different types and three different classes. Type 1 helmets incorporate a full brim (brim fully encircles the dome of the hat) Type 2 helmets have no encircling brim, but may include a short bill on the front

Helmet Class (Pre-1987) Regarding electrical performance, ANSI Z89.1-1986 recognizes three classes: Class A Helmets reduce the force of impact of falling objects and also reduce the danger of contact with exposed low-voltage electrical conductors. Helmet shells are proof-tested at 2,200 volts of electrical charge. Class B Helmets reduce the force of impact of falling objects and also reduce the danger of contact with exposed high-voltage electrical conductors. Helmet shells are proof-tested at 20,000 volts. Class C Helmets reduce the force of impact of falling objects, but offer no electrical protection.

Helmet Type (After 1986) ANSI Z89.1-2003 no longer uses Type 1 and Type 2 to describe the brim characteristics of a protective helmet. The new Type designation is as follows: Type I helmets offer protection from blows to the top of the head Type II helmets offer protection from blows to both the top and sides of the head

Helmet Class (After 1986) Class G (General) Helmets -This is equivalent to the old Class A. Class G helmets are proof tested at 2,200 volts. Class E (Electrical) Helmets - This is equivalent to the old Class B. Class E helmets are proof tested at 20,000 volts. Class C (Conductive) Helmets - This class provides no electrical insulation; the class designation did not change from the old standard.

ANSI Markings The following information must be marked inside the helmet Manufacturer's name The “ANSI Z89.1-1997" designation Class designation (G, E or C) Date of manufacture

Protective Footwear 1910.136(a) Employees must use protective footwear when falling or rolling objects, objects piercing the sole, employee's feet are exposed to electrical hazards.

ANSI Markings – Footwear 1910.136(b)(1)-(2) Protective footwear purchased after July 5, 1994 shall comply with ANSI Z41-1991 Protective footwear purchased before July 5, 1994 shall comply with the ANSI Z41.1-1967

ANSI Markings – Footwear 1910.136(b)(1) Indicates ANSI standard met PT indicates “protective toe” portion of standard Indicates Male or Female Impact resistance Compression (Cd) resistance conductive properties (EH) electrical hazard (Mt) metatarsal resistance rating, (PR) puncture resistance (SD) static dissipative properties.

EH Footwear Electrical shock resistant (EH) footwear is manufactured with non-conductive electrical shock resistant soles and heals. It must be capable of withstanding the application of 14,000 volts at 60 hertz for one minute with no current flow or leakage current in excess of 3.0 milliamperes, under dry conditions.

ASTM Designations After March 2005 On March 2005, ANSI Z41 was replaced by two new American Society of Testing Material (ASTM) International Standards. The new ASTM standards are: F2412-05 Standard Test Methods for Foot Protection F2413-05 Standard Specification for Performance Requirements for Foot Protection.

ASTM Designations After March 2005 ASTM F2413-05 M I/75/C/75/Mt75 PR CS Indicates ASTM standard met Indicates Male or Female Impact resistance Compression resistance (Mt) metatarsal resistance rating (Cd) conductive properties (CS) chain saw cut resistance (DI)dielectric insulation (EH) electrical hazard (PR) puncture resistance (SD) static dissipative properties

Insulating Blankets 1910.137(a) - 1910.137(a)(1)(ii)(G) Insulating blankets, matting, covers, line hose, gloves, and sleeves made of rubber shall meet the following requirements: Manufacture and marking Blankets, gloves, and sleeves shall be produced by a seamless process. Each item shall be marked with its classification (i.e. Class 0 – Class 4) REMEMBER: Non-ozone-resistant will be marked “Type I” Ozone-resistant will be marked “Type II”

Employee Owned PPE 1910.132(b) If an employee provides their own protective equipment, the employer shall be responsible to assure its adequacy, including proper maintenance, and sanitation of such equipment.

Insulated Tools 1910.335(a)(2)(i) When working near exposed conductors the employee must use insulated tools or handling equipment

Employee Training 1910.132(f)(1) – (1)(v) When PPE is required, the employer must cover the following areas: When PPE is necessary; What PPE is necessary; How to properly don and doff PPE How to adjust and wear PPE; The limitations of the PPE; and, The proper care, maintenance, useful life and disposal of the PPE.

Training Documentation 1910.132(f)(4) The employer must issue a written “training certificate” which must include: the name of each employee trained, the date(s) of training, and Identity of the subject covered

Back to top button